WebRTC browser calls FreePBX 13 (Stable)
After upgrade to FreePBX 13 UCP WebRTC calls disconnect everytime. I am use Chrome. Login to UCP using extention Enable WebRTC in User Manager, added STUN and TURN google server...
View ArticleClik here to view.
Network setup with two SIP trunks
No problem Blaze, but what is the normal protocol on this board regarding the showing of public ip addresses etc ? A wireshark trace without these is going to be pretty meaningless but the client is...
View ArticleHA and upgrade to FreePBX 13
Any news about upgrading a FreePBX High Availability system to FreePBX 13?Our distro version is 6.12.65-29.
View ArticleCDR - Giving a client only access to his CDR records
how can we do that? I have no programming expertise.
View ArticleCDR - Giving a client only access to his CDR records
You don't need programming expertise.Just create a UCP account from FreePBX GUI and tie all extensions to it, for which you want to see call...
View ArticleWebrtc will not load
latest version of webrtc installed i can see the module.when i place a call i get this errorgetUserMedia() no longer works on insecure origins. To use this feature, you should consider switching your...
View ArticleCDR - Giving a client only access to his CDR records
Again, the UCP will show all the CDRs for extensions you want. Yes, I know. But what it won't do is Show all of them in a SINGLE report. So if you have 20 extensions you have 20 reports. It doesn't...
View ArticleCDR - Giving a client only access to his CDR records
Ok, I did that and i get the CRD page only. The problem is that i see all the CDR records even though I set the extensuion range in the user setup. I am using asterisk 11.4.0 and FreePBX 2.11.0.38 if...
View ArticleNetwork setup with two SIP trunks
@jon_b You can use the sip debug tools for this and yes, you'll have to edit the results if you don't want to show the IPs. But you need to say something like XX.XX.XX.XX is the trunk and YY.YY.YY.YY...
View ArticleCDR - Giving a client only access to his CDR records
@amertel I'm am not familiar with that version. So I can't say if the UCP will work right with it. Is it actually UCP or User Panel? Those are two different things.
View ArticleCDR - Giving a client only access to his CDR records
under ADMIN: ADMINISTRATOR it shows on the upper right Add UseradminewadminnewFBXtechPioneershah I guess that is just user? Not UCP?
View ArticleCDR - Giving a client only access to his CDR records
Do you go to http://ip-of-box/ucp or /recordings to get into the user portal?
View ArticleCDR - Giving a client only access to his CDR records
Also, I don't believe that FreePBX 2.11 is supported anymore, so it's going to be hard to get help. Probably can but I'm not sure.
View ArticleCDR - Giving a client only access to his CDR records
I went to the admin tab (top left) and clicked on it and then clicked on adminstrators to get the drop down box i pasted where would i do http://ip-of-box/ucp?
View ArticleCDR - Giving a client only access to his CDR records
I am going away for now. Will check back in a couple of hours. Thanks to everyone for their help. It is greatly appreciated
View ArticleHA and upgrade to FreePBX 13
Wiki was updated last week for this http://wiki.freepbx.org/display/FPG/Upgrading+a+HA+System+from+6.12.65+to+10.13.66
View ArticleClik here to view.
HA and upgrade to FreePBX 13
Not sure what is meant by "upgrading is only possible when you are running FreePBX 13.I am running FreePBX 12, but would like to upgrade to 13. I assume this should be: "upgrading is only possible...
View ArticleNetwork setup with two SIP trunks
OK, here goes (part 1) Here is a normal incoming call to the Telco 1 Trunk. This is the working trunk on a private network. As the call is established near the bottom of the trace, you will find the...
View ArticleNetwork setup with two SIP trunks
Part 2.... Next up is an incoming call to the Telco 2 trunk which is via the Internet. This call sets up correctly, rings the target extension and can be answered, but there is no audio. I've just...
View ArticleNetwork setup with two SIP trunks
So you are having one way or two way audio issues? And do you have the PBX setup to do NAT? Because this is completely a networking configuration issue. With all the private LANs I'm seeing and the...
View Article