Upgrading from FreePBX 13 to 14 on centos 6.9
Hi I have a freepbx 13 running on a centos 6.9 server with php 5.3.3. When I want to upgrade via the admin control panel, I get 2 errors during pre check. nodejs is not installed PHP 5.6 or higher...
View ArticleClik here to view.
Calling another local PBX goes strait to Voicemail
See this post. Act as SIP Trunk Provider - Connect FreePBX to Panasonic TDE600/200 General Help Hi Community, I figure out what do to. In order help other with a similar issue here are my steps that I...
View ArticleFreePBX Firewall Service not running after update
What i would do: fwconsole firewall stop fwconsole ma delete firewall fwconsole reload fwconsole ma downloadinstall firewall fwconsole reload fwconsole firewall start
View ArticleBlind Transfer callback if not answered after n time
Here’s where park feature comes in. Take a look at the parking module, see if you can adopt this instead of transferring
View ArticleInbound calls drop after 30 seconds
This topic was automatically closed 7 days after the last reply. New replies are no longer allowed.
View ArticleClik here to view.
Calls between PBXes
@dickson , +1 on the IAX setup. dickson: QoS wont’ be an issue not for a few demo calls. I disagree here. A small organization may have DSL or low-end cable service with only 1 or 2 Mbps upload....
View ArticleFreepbx 14 error after upgrade
I’m not 100% sure, but I think this error comes from attempting to log in too quickly after the system boots up. This thread may be related.
View ArticleFreePBX Firewall Service not running after update
Hello, I followed your advice and the problem persist. I still see the red x on my dashboard. Regards,
View ArticleOutbound call drops after 30 seconds
I have set “RTP Timeout” and “RTP Hold Timeout” to 3600, now the calls seem to last longer than 30 seconds. I guess the RTP Timeout (which was set to 30) caused this issue. Hoping the outbound calls...
View ArticleClik here to view.
HELP! Just did the latest update, FreePBX reports "Tampered File"
computertechs: think something is borked with signature retrieval in the upgrade process. Nope. That’s not the issue. Upgrade framework and all will be resolved.
View ArticleFreepbx page is blank
After restarting the system, white screen started again. Ran through a list of commands given before. fwconsole ma enableall fwconsole ma upgradeall fwconsole ma upgrade framework --edge fwconsole...
View ArticleCalls between PBXes
That is completely true, production yes for sure you need QOS. I was approaching his situation from a demo perspective. If call quality is bad, it could be quickly identified as a firewall or...
View ArticleBlind Transfer callback if not answered after n time
Pitz, When I park a call yes it does the ring back after a predetermined time, BUT I can’t see the call as when I transfer it. When I park it I would have to tell the intended extension “hey there is...
View ArticleSame Extension on Multiple Phones
So is multiple phones on one extension only possible with PJSIP, not chan_sip? On v13 and can’t find the “contacts” field on my extension (which is chan_sip). Thanks.
View ArticleInbound calls randomly directed to non-reception number
Modules upgraded over the weekend, suddenly I have some random behavior where inbound calls go to an emergency extension (an internal extension that routes to an external cell phone) instead of...
View ArticleUpgrading from FreePBX 13 to 14 on centos 6.9
As a non-expert, I recommend you run the FreePBX Distro. Install ver. 13 and use Backup and Restore to move your current config or install ver. 14 and use this to migrate your settings:...
View ArticleAct as SIP Trunk Provider - Connect FreePBX to Panasonic TDE600/200
Do you know if these setting will work on a KX-NCP500 with a DSP16 Card? I tried following your method and the FreePbx just hangs when calling a Panasonic Extension. Thanks!
View ArticleInbound calls randomly directed to non-reception number
https://wiki.freepbx.org/display/SUP/Providing+Great+Debug#ProvidingGreatDebug-AsteriskLogs
View Article