Upgraded to FreePBX Distro 10.13.66-9 - lost my TE133
I think we are drifting away from the actual problem here - I have no problem creating the configs necessary - the DAHDI 2.11.0 that comes pre-packaged with the Distro Upgrade would not bring my TE133...
View ArticleClik here to view.
Status of Zulu UC
GSnover: since Zulu requires me to answer the station-leg before it initiates the outbound leg, it is not all that useful and we have not show it to clients This was resolved and released yesterday
View ArticleClik here to view.
Upgraded to FreePBX Distro 10.13.66-9 - lost my TE133
As I said "It is a nice attempt to configure dahdi, but is IMHO limited and sometimes a little intrusive" and you said "This would have been crushing if I was afraid of compiling from source (which I...
View ArticleFreePBX Distro - If you upgrade to iSymphony 3.3.0.30 you need JRE 1.8
Actually, 1.8 IS in the repos - so you need to update.
View ArticleClik here to view.
Call via internal trunk wont route internally
Hi Dave, If you check my original post you will see i mentioned the trunk works from the elastix pbx to the freepbx fine, in the opposite direction however it goes straight to the external trunk...
View ArticleP users being logged out every 15 minutes
Thanks. Will fix tomorrow. PS: Hope you actually drive a Tesla!
View ArticleBLF hints for flow control not working correctly
Thanks. I upgraded everything to the latest levels while waiting for a reply. Will check in the morning.
View ArticleUpgraded to FreePBX Distro 10.13.66-9 - lost my TE133
Note that when Greg says "DAHDI 2.11.0" he is NOT talking about the FreePBX module. He is talking about the Version of Dahdi for Asterisk
View ArticleFax, no matching endpoint
Hello All. How can I get a Step by Step Guide on hot to receive faxes and send them to and Email. I keep getting no matching end poinds found when a configured as explained in The FreePBX topic...
View ArticleFreepbx 13 ucp missing fax to email field
A post was split to a new topic: Fax, no matching endpoint
View ArticleClik here to view.
AD userman integration error
When I try and save the AD details, I get the following exception. The details are still saving however, and it says connected when I revisit the page.This is a totally new install as well, using...
View ArticleAastra Firmware Version Recomendations
I've not been able to find much information about what version of the Aastra firmware works best with the new phone apps. I did find this little gem in the wiki: "For the Aastra 6730i, 6731i, and...
View ArticleQueues and Commercial EPM question
Hey Tony, and your right I did a crud job with that paste, it does say 45%line1Ext% and I guess the starting * got dropped in the prior copy and paste, sorry about that one. That said, it sounds like...
View ArticleFreePBX help
Our reception is set to extension 1000, we have an extension board that flashes when someone callsa number in our offices. If someone calls a number the board flashes red showing which extension...
View ArticleCannot dial through an IVR
This is a new install of 10.13.66-1 using Asteisk 13.7.2. The install is less than a week old. We are using SIP trunks set for dtmfmode=rfc2833. When they dial into an IVR somewhere (example was an...
View ArticleAsterisk to Avaya BCM450
Hello, I have been reading for a few weeks trying to get asterisk to avaya bcm calling working, i have it working by asterisk going to the bcm IVR and then selecting extension, I would like to be able...
View ArticleClik here to view.
Aastra Firmware Version Recomendations
I would say whatever is supported in the EPM should be supported by the restapps. I'm showing the following for Aastra. Pasted image242x799 9.96 KB
View Article