Of course, I did, but I apparently thought that it was something else quite disappointed.

[root@freepbx ~]# cat /etc/sangoma-release
Sangoma Linux release 7.5.1805 (Core)
[root@freepbx ~]# /etc/schmooze/pbx-version
/etc/schmooze/pbx-version: line 1: 12.7.5-1807-1.sng7: command not found

Shall I reinstall FreePBX again

I don’t think you need to reinstall, just yet. You can try

cp /etc/asterisk/modules.conf /etc/asterisk/modules.conf.bak
cp /dev/null /etc/asterisk/modules.conf
chown asterisk. /etc/asterisk/modules.conf

Do the Apply Config after that. It should re-write your modules.conf and we can go from there.

I have a site with a SIP trunk from Nextiva that occasionally fails to register. It will be working fine for days and then suddenly drops off. It just gives unreachable error in the logs. If I reboot the PBX it will register again sometimes for a few hours or a few days. I even have to reboot the router sometimes to get it to stay registered for more than 30 minutes. Sangoma PBXact 40 Version 14.0.5.2 Sonicwall Router with firewall configured according to Nextiva’s requirements
I have several other sites with Nextiva trunks with no issues using the same trunk parameters. The other sites use a different router.
Any thoughts?

We do try to fully document what is available in Queue Wallboard. There is nothing about it that says operator panel.

https://wiki.freepbx.org/display/FPG/Queue+Wallboard

Connected to Asterisk 13.22.0 currently running on freepbx (pid = 2529)
[2018-11-27 02:54:58] ERROR[2529]: config_options.c:708 aco_process_config: Unable to load config file ‘statsd.conf’
[2018-11-27 02:54:58] ERROR[2529]: res_sorcery_config.c:261 sorcery_config_internal_load: Unable to load config file ‘codecs.conf’
[2018-11-27 02:54:58] ERROR[2529]: res_sorcery_config.c:261 sorcery_config_internal_load: Unable to load config file ‘pjproject.conf’
[2018-11-27 02:54:59] ERROR[2529]: res_pjsip_config_wizard.c:1089 object_type_loaded_observer: Unable to load config file ‘pjsip_wizard.conf’
[2018-11-27 02:54:59] ERROR[2529]: res_pjsip_config_wizard.c:1089 object_type_loaded_observer: Unable to load config file ‘pjsip_wizard.conf’
[2018-11-27 02:54:59] ERROR[2529]: res_pjsip_config_wizard.c:1089 object_type_loaded_observer: Unable to load config file ‘pjsip_wizard.conf’
[2018-11-27 02:54:59] NOTICE[2529]: res_smdi.c:982 smdi_load: Unable to load config smdi.conf: SMDI disabled
[2018-11-27 02:54:59] NOTICE[2529]: res_smdi.c:1403 load_module: No SMDI interfaces are available to listen on, not starting SMDI listener.
[2018-11-27 02:54:59] ERROR[2529]: res_phoneprov.c:1357 load_common: Unable to load config phoneprov.conf
[2018-11-27 02:54:59] ERROR[2529]: res_phoneprov.c:1430 load_module: Unable to load provisioning profiles.
[2018-11-27 02:54:59] WARNING[2529]: res_stun_monitor.c:340 load_config: Unable to load config res_stun_monitor.conf
[2018-11-27 02:54:59] ERROR[2529]: config_options.c:708 aco_process_config: Unable to load config file ‘hep.conf’
[2018-11-27 02:54:59] ERROR[2529]: res_calendar.c:1055 load_config: Unable to load config calendar.conf
[2018-11-27 02:54:59] NOTICE[2529]: codec_siren14.c:670 load_module: ITU G.722.1 Annex C (Siren14, licensed from Polycom) transcoding module version 13.0_1.0.7
[2018-11-27 02:54:59] NOTICE[2529]: codec_siren14.c:671 load_module: Copyright © 1999-2009 Digium, Inc.
[2018-11-27 02:54:59] NOTICE[2529]: codec_siren14.c:672 load_module: This module is supplied under a commercial license granted by Digium, Inc.
[2018-11-27 02:54:59] NOTICE[2529]: codec_siren14.c:673 load_module: Please see the full license text supplied in the accompanying
[2018-11-27 02:54:59] NOTICE[2529]: codec_siren14.c:674 load_module: “LICENSE” file, or ask for a copy from Digium.
[2018-11-27 02:54:59] NOTICE[2529]: codec_siren14.c:675 load_module: This product includes software from the Speex library. Please see
[2018-11-27 02:54:59] NOTICE[2529]: codec_siren14.c:676 load_module: the accompanying “SPEEX_LICENSE” file for license information.
[2018-11-27 02:54:59] NOTICE[2529]: codec_siren7.c:639 load_module: ITU G.722.1 (Siren7, licensed from Polycom) transcoding module version 13.0_1.0.7
[2018-11-27 02:54:59] NOTICE[2529]: codec_siren7.c:640 load_module: Copyright © 1999-2009 Digium, Inc.
[2018-11-27 02:54:59] NOTICE[2529]: codec_siren7.c:641 load_module: This module is supplied under a commercial license granted by Digium, Inc.
[2018-11-27 02:54:59] NOTICE[2529]: codec_siren7.c:642 load_module: Please see the full license text supplied in the accompanying
[2018-11-27 02:54:59] NOTICE[2529]: codec_siren7.c:643 load_module: “LICENSE” file, or ask for a copy from Digium.
[2018-11-27 02:54:59] ERROR[2529]: pbx_lua.c:1635 load_or_reload_lua_stuff: Error loading extensions.lua: cannot open ‘/etc/asterisk/extensions.lua’ for reading: No such file or directory
[2018-11-27 02:54:59] WARNING[2529]: res_pktccops.c:1040 load_pktccops_config: Unable to load config file res_pktccops.conf
[2018-11-27 02:54:59] ERROR[2529]: res_config_ldap.c:1827 parse_config: Cannot load configuration file: res_ldap.conf
[2018-11-27 02:54:59] ERROR[2529]: res_config_ldap.c:1720 load_module: Cannot load LDAP RealTime driver.
[2018-11-27 02:54:59] ERROR[2529]: res_config_sqlite.c:733 load_config: Unable to load res_config_sqlite.conf
[2018-11-27 02:54:59] ERROR[2529]: res_config_sqlite3.c:1265 parse_config: Missing config file ‘res_config_sqlite3.conf’
[2018-11-27 02:54:59] ERROR[2529]: res_pjsip_endpoint_identifier_ip.c:403 ip_identify_apply: Identify ‘10-identify’ is not configured to match anything.
[2018-11-27 02:54:59] ERROR[2529]: res_sorcery_config.c:338 sorcery_config_internal_load: Could not create an object of type ‘identify’ with id ‘10-identify’ from configuration file ‘pjsip.conf’
[2018-11-27 02:54:59] ERROR[2529]: res_pjsip_endpoint_identifier_ip.c:403 ip_identify_apply: Identify ‘20-identify’ is not configured to match anything.
[2018-11-27 02:54:59] ERROR[2529]: res_sorcery_config.c:338 sorcery_config_internal_load: Could not create an object of type ‘identify’ with id ‘20-identify’ from configuration file ‘pjsip.conf’
[2018-11-27 02:54:59] ERROR[2529]: res_pjsip_endpoint_identifier_ip.c:403 ip_identify_apply: Identify ‘30-identify’ is not configured to match anything.
[2018-11-27 02:54:59] ERROR[2529]: res_sorcery_config.c:338 sorcery_config_internal_load: Could not create an object of type ‘identify’ with id ‘30-identify’ from configuration file ‘pjsip.conf’
[2018-11-27 02:54:59] ERROR[2529]: res_pjsip_endpoint_identifier_ip.c:403 ip_identify_apply: Identify ‘2501-identify’ is not configured to match anything.
[2018-11-27 02:54:59] ERROR[2529]: res_sorcery_config.c:338 sorcery_config_internal_load: Could not create an object of type ‘identify’ with id ‘2501-identify’ from configuration file ‘pjsip.conf’
[2018-11-27 02:54:59] ERROR[2529]: res_pjsip_endpoint_identifier_ip.c:403 ip_identify_apply: Identify ‘1101-identify’ is not configured to match anything.
[2018-11-27 02:54:59] ERROR[2529]: res_sorcery_config.c:338 sorcery_config_internal_load: Could not create an object of type ‘identify’ with id ‘1101-identify’ from configuration file ‘pjsip.conf’
[2018-11-27 02:54:59] ERROR[2529]: res_pjsip_endpoint_identifier_ip.c:403 ip_identify_apply: Identify ‘2101-identify’ is not configured to match anything.
[2018-11-27 02:54:59] ERROR[2529]: res_sorcery_config.c:338 sorcery_config_internal_load: Could not create an object of type ‘identify’ with id ‘2101-identify’ from configuration file ‘pjsip.conf’
[2018-11-27 02:54:59] ERROR[2529]: res_pjsip_endpoint_identifier_ip.c:403 ip_identify_apply: Identify ‘3101-identify’ is not configured to match anything.
[2018-11-27 02:54:59] ERROR[2529]: res_sorcery_config.c:338 sorcery_config_internal_load: Could not create an object of type ‘identify’ with id ‘3101-identify’ from configuration file ‘pjsip.conf’
[2018-11-27 02:54:59] ERROR[2529]: res_pjsip_endpoint_identifier_ip.c:403 ip_identify_apply: Identify ‘2201-identify’ is not configured to match anything.
[2018-11-27 02:54:59] ERROR[2529]: res_sorcery_config.c:338 sorcery_config_internal_load: Could not create an object of type ‘identify’ with id ‘2201-identify’ from configuration file ‘pjsip.conf’
[2018-11-27 02:54:59] ERROR[2529]: res_pjsip_endpoint_identifier_ip.c:403 ip_identify_apply: Identify ‘2301-identify’ is not configured to match anything.
[2018-11-27 02:54:59] ERROR[2529]: res_sorcery_config.c:338 sorcery_config_internal_load: Could not create an object of type ‘identify’ with id ‘2301-identify’ from configuration file ‘pjsip.conf’
[2018-11-27 02:54:59] ERROR[2529]: res_pjsip_endpoint_identifier_ip.c:403 ip_identify_apply: Identify ‘2401-identify’ is not configured to match anything.
[2018-11-27 02:54:59] ERROR[2529]: res_sorcery_config.c:338 sorcery_config_internal_load: Could not create an object of type ‘identify’ with id ‘2401-identify’ from configuration file ‘pjsip.conf’
[2018-11-27 02:54:59] ERROR[2529]: res_pjsip_endpoint_identifier_ip.c:403 ip_identify_apply: Identify ‘2601-identify’ is not configured to match anything.
[2018-11-27 02:54:59] ERROR[2529]: res_sorcery_config.c:338 sorcery_config_internal_load: Could not create an object of type ‘identify’ with id ‘2601-identify’ from configuration file ‘pjsip.conf’
[2018-11-27 02:54:59] ERROR[2529]: res_pjsip_endpoint_identifier_ip.c:403 ip_identify_apply: Identify ‘3201-identify’ is not configured to match anything.
[2018-11-27 02:54:59] ERROR[2529]: res_sorcery_config.c:338 sorcery_config_internal_load: Could not create an object of type ‘identify’ with id ‘3201-identify’ from configuration file ‘pjsip.conf’
[2018-11-27 02:54:59] ERROR[2529]: res_pjsip_endpoint_identifier_ip.c:403 ip_identify_apply: Identify ‘3301-identify’ is not configured to match anything.
[2018-11-27 02:54:59] ERROR[2529]: res_sorcery_config.c:338 sorcery_config_internal_load: Could not create an object of type ‘identify’ with id ‘3301-identify’ from configuration file ‘pjsip.conf’
[2018-11-27 02:54:59] ERROR[2529]: res_pjsip_endpoint_identifier_ip.c:403 ip_identify_apply: Identify ‘3401-identify’ is not configured to match anything.
[2018-11-27 02:54:59] ERROR[2529]: res_sorcery_config.c:338 sorcery_config_internal_load: Could not create an object of type ‘identify’ with id ‘3401-identify’ from configuration file ‘pjsip.conf’
[2018-11-27 02:54:59] ERROR[2529]: res_pjsip_endpoint_identifier_ip.c:403 ip_identify_apply: Identify ‘1201-identify’ is not configured to match anything.
[2018-11-27 02:54:59] ERROR[2529]: res_sorcery_config.c:338 sorcery_config_internal_load: Could not create an object of type ‘identify’ with id ‘1201-identify’ from configuration file ‘pjsip.conf’
[2018-11-27 02:54:59] ERROR[2529]: res_pjsip_endpoint_identifier_ip.c:403 ip_identify_apply: Identify ‘1301-identify’ is not configured to match anything.
[2018-11-27 02:54:59] ERROR[2529]: res_sorcery_config.c:338 sorcery_config_internal_load: Could not create an object of type ‘identify’ with id ‘1301-identify’ from configuration file ‘pjsip.conf’
[2018-11-27 02:54:59] ERROR[2529]: res_pjsip_endpoint_identifier_ip.c:403 ip_identify_apply: Identify ‘1401-identify’ is not configured to match anything.
[2018-11-27 02:54:59] ERROR[2529]: res_sorcery_config.c:338 sorcery_config_internal_load: Could not create an object of type ‘identify’ with id ‘1401-identify’ from configuration file ‘pjsip.conf’
[2018-11-27 02:54:59] ERROR[2529]: res_pjsip_endpoint_identifier_ip.c:403 ip_identify_apply: Identify ‘1501-identify’ is not configured to match anything.
[2018-11-27 02:54:59] ERROR[2529]: res_sorcery_config.c:338 sorcery_config_internal_load: Could not create an object of type ‘identify’ with id ‘1501-identify’ from configuration file ‘pjsip.conf’
[2018-11-27 02:54:59] ERROR[2529]: res_pjsip_endpoint_identifier_ip.c:403 ip_identify_apply: Identify ‘1601-identify’ is not configured to match anything.
[2018-11-27 02:54:59] ERROR[2529]: res_sorcery_config.c:338 sorcery_config_internal_load: Could not create an object of type ‘identify’ with id ‘1601-identify’ from configuration file ‘pjsip.conf’
[2018-11-27 02:54:59] ERROR[2529]: res_pjsip_endpoint_identifier_ip.c:403 ip_identify_apply: Identify ‘1701-identify’ is not configured to match anything.
[2018-11-27 02:54:59] ERROR[2529]: res_sorcery_config.c:338 sorcery_config_internal_load: Could not create an object of type ‘identify’ with id ‘1701-identify’ from configuration file ‘pjsip.conf’
[2018-11-27 02:54:59] ERROR[2529]: res_pjsip_endpoint_identifier_ip.c:403 ip_identify_apply: Identify ‘1801-identify’ is not configured to match anything.
[2018-11-27 02:54:59] ERROR[2529]: res_sorcery_config.c:338 sorcery_config_internal_load: Could not create an object of type ‘identify’ with id ‘1801-identify’ from configuration file ‘pjsip.conf’
[2018-11-27 02:54:59] ERROR[2529]: res_pjsip_endpoint_identifier_ip.c:403 ip_identify_apply: Identify ‘1901-identify’ is not configured to match anything.
[2018-11-27 02:54:59] ERROR[2529]: res_sorcery_config.c:338 sorcery_config_internal_load: Could not create an object of type ‘identify’ with id ‘1901-identify’ from configuration file ‘pjsip.conf’
[2018-11-27 02:54:59] ERROR[2529]: res_pjsip_endpoint_identifier_ip.c:403 ip_identify_apply: Identify ‘3801-identify’ is not configured to match anything.
[2018-11-27 02:54:59] ERROR[2529]: res_sorcery_config.c:338 sorcery_config_internal_load: Could not create an object of type ‘identify’ with id ‘3801-identify’ from configuration file ‘pjsip.conf’
[2018-11-27 02:54:59] ERROR[2529]: res_pjsip_config_wizard.c:1089 object_type_loaded_observer: Unable to load config file ‘pjsip_wizard.conf’
[2018-11-27 02:54:59] WARNING[2529]: format_cap.c:404 ast_format_cap_update_by_allow_disallow: Cannot allow unknown format ‘silk’
freepbx*CLI>
Broadcast message from root@freepbx.sangoma.local (Tue Nov 27 02:55:03 2018):

Firewall service now starting.

[2018-11-27 02:55:05] WARNING[2529]: iax2/firmware.c:237 iax_firmware_reload: Error opening firmware directory ‘/var/lib/asterisk/firmware/iax’: No such file or directory
[2018-11-27 02:55:05] NOTICE[2529]: iax2/provision.c:562 iax_provision_reload: No IAX provisioning configuration found, IAX provisioning disabled.
[2018-11-27 02:55:05] NOTICE[2529]: chan_console.c:1445 load_config: Unable to open configuration file console.conf!
[2018-11-27 02:55:05] NOTICE[2529]: chan_mgcp.c:4697 reload_config: Unable to load config mgcp.conf, MGCP disabled
SIP channel loading…
[2018-11-27 02:55:05] NOTICE[2529]: chan_sip.c:31569 build_peer: The ‘username’ field for sip peers has been deprecated in favor of the term ‘defaultuser’
[2018-11-27 02:55:06] WARNING[2529]: chan_sip.c:32064 display_nat_warning: !!! PLEASE NOTE: Setting ‘nat’ for a peer/user that differs from the global setting can make
[2018-11-27 02:55:06] WARNING[2529]: chan_sip.c:32065 display_nat_warning: !!! the name of that peer/user discoverable by an attacker. Replies for non-existent peers/users
[2018-11-27 02:55:06] WARNING[2529]: chan_sip.c:32066 display_nat_warning: !!! will be sent to a different port than replies for an existing peer/user. If at all possible,
[2018-11-27 02:55:06] WARNING[2529]: chan_sip.c:32067 display_nat_warning: !!! use the global ‘nat’ setting and do not set ‘nat’ per peer/user.
[2018-11-27 02:55:06] WARNING[2529]: chan_sip.c:32068 display_nat_warning: !!! (config category=‘voxbeam_outbound’ global force_rport=‘Yes’ peer/user force_rport=‘No’)
[2018-11-27 02:55:06] NOTICE[2529]: chan_skinny.c:8452 config_load: Configuring skinny from skinny.conf
[2018-11-27 02:55:06] NOTICE[2529]: chan_skinny.c:8462 config_load: Unable to load config skinny.conf, Skinny disabled.
[2018-11-27 02:55:06] ERROR[2529]: chan_mobile.c:4778 load_module: No Bluetooth devices found. Not loading module.
[2018-11-27 02:55:06] NOTICE[2529]: chan_ooh323.c:2831 reload_config: Unable to load config ooh323.conf, OOH323 disabled
[2018-11-27 02:55:06] ERROR[2529]: chan_ooh323.c:3965 load_module: Can’t load ooh323 config file, OOH323 Disabled
[2018-11-27 02:55:06] ERROR[2529]: res_pjsip_config_wizard.c:1089 object_type_loaded_observer: Unable to load config file ‘pjsip_wizard.conf’
[2018-11-27 02:55:06] ERROR[2529]: res_pjsip_config_wizard.c:1089 object_type_loaded_observer: Unable to load config file ‘pjsip_wizard.conf’
[2018-11-27 02:55:06] WARNING[2529]: res_phoneprov.c:1526 ast_phoneprov_provider_register: Provider ‘res_pjsip_phoneprov_provider’ cannot be registered: res_phoneprov not loaded.
[2018-11-27 02:55:06] ERROR[2529]: res_pjsip_phoneprov_provider.c:389 load_module: Unable to register pjsip phoneprov provider.
[2018-11-27 02:55:06] ERROR[2529]: config_options.c:708 aco_process_config: Unable to load config file ‘agents.conf’
[2018-11-27 02:55:06] ERROR[2529]: app_agent_pool.c:2695 load_module: Unable to load config. Not loading module.
[2018-11-27 02:55:06] NOTICE[2529]: confbridge/conf_config_parser.c:2089 verify_default_profiles: Adding default_menu menu to app_confbridge
[2018-11-27 02:55:06] WARNING[2529]: res_calendar.c:538 ast_calendar_register: Calendar support disabled, not loading caldav calendar module
[2018-11-27 02:55:06] WARNING[2529]: res_calendar.c:538 ast_calendar_register: Calendar support disabled, not loading ews calendar module
[2018-11-27 02:55:06] WARNING[2529]: res_calendar.c:538 ast_calendar_register: Calendar support disabled, not loading exchange calendar module
[2018-11-27 02:55:06] WARNING[2529]: res_calendar.c:538 ast_calendar_register: Calendar support disabled, not loading ical calendar module
[2018-11-27 02:55:06] ERROR[2529]: cdr_custom.c:101 load_config: Unable to load cdr_custom.conf. Not logging custom CSV CDRs.
[2018-11-27 02:55:06] WARNING[2529]: cdr_manager.c:214 load_config: Failed to load configuration file. Module not activated.
[2018-11-27 02:55:07] ERROR[2529]: cdr_syslog.c:145 load_config: Unable to load cdr_syslog.conf. Not logging custom CSV CDRs to syslog.
[2018-11-27 02:55:07] ERROR[2529]: cel_custom.c:92 load_config: Unable to load cel_custom.conf. Not logging CEL to custom CSVs.
[2018-11-27 02:55:07] WARNING[2529]: cdr_odbc.c:206 odbc_load_module: cdr_odbc: Unable to load config for ODBC CDR’s: cdr_odbc.conf
[2018-11-27 02:55:07] WARNING[2529]: app_festival.c:570 load_module: No such configuration file festival.conf
[2018-11-27 02:55:07] WARNING[2529]: app_followme.c:414 reload_followme: No follow me config file (followme.conf), so no follow me
[2018-11-27 02:55:07] WARNING[2529]: app_minivm.c:2910 load_config: Failed to load configuration file. Module activated with default settings.
[2018-11-27 02:55:07] ERROR[2529]: chan_phone.c:1413 load_module: Unable to load config phone.conf
[2018-11-27 02:55:07] ERROR[2529]: chan_unistim.c:6781 reload_config: Unable to load config unistim.conf
[2018-11-27 02:55:07] WARNING[2529]: res_hep_pjsip.c:240 load_module: res_hep is not loaded or running; declining module load
[2018-11-27 02:55:07] WARNING[2529]: res_hep_rtcp.c:163 load_module: res_hep is not loaded or running; declining module load
[2018-11-27 02:55:07] NOTICE[2529]: pbx_ael.c:172 pbx_load_module: File /etc/asterisk/extensions.ael not found; AEL declining load
[2018-11-27 02:55:07] ERROR[2529]: res_clialiases.c:198 load_config: res_clialiases configuration file ‘cli_aliases.conf’ not found
[2018-11-27 02:55:07] ERROR[2529]: pbx_dundi.c:4832 set_config: Unable to load config dundi.conf
[2018-11-27 02:55:07] WARNING[2529]: app_voicemail.c:13872 actual_load_config: maxsilence should be less than minsecs or you may get empty messages
[2018-11-27 02:55:07] WARNING[2529]: app_flite.c:76 read_config: Flite: Unable to read config file flite.conf. Using default settings
[2018-11-27 02:55:07] NOTICE[2529]: func_odbc.c:1784 load_module: Unable to load config for func_odbc: func_odbc.conf
[2018-11-27 02:55:07] WARNING[2529]: cdr_mysql.c:482 my_load_module: Unable to load config for mysql CDR’s: cdr_mysql.conf
Asterisk Ready.
[2018-11-27 02:55:10] NOTICE[3158]: chan_sip.c:30180 sip_poke_noanswer: Peer ‘geils_outbound’ is now UNREACHABLE! Last qualify: 0

OK, so whoever did this didn’t do it right or really screwed something up. If re-installing is an option, do that. Otherwise you’re going to trying fixing every little issue that pops up after you’ve fixed the previous issue.

OK. This is a VM. I will reboot the VM with ISO mounted a reinstall again. Thanks a lot for the help. I will post again here with news if a reinstall did it right.

Any comments you want to give me during the fresh installation?

https://wiki.freepbx.org/display/PPS/Installing+SNG7+Official+Distro

Adding an index would probably help if there isn’t one, from, mysql :-

SHOW INDEXES FROM del;

if not there then

ALTER TABLE cel ADD INDEX eventtime (eventtime);

I discovered the reason for these errors: backup/restore. The system works well when freshly installed. After restoring a full backup taken from an old system, everything crashes. Any comments?

What version is the old system?

Free PBX Version: 12.7.5-1807-1.sng7
Endpoint Manager: 14.0.2.155
Device Make: Panasonic
Device Model: KX-TGP600

• Currently have three extensions setup for use by phones connected to the KX-TGP600
• Each extension is setup using Endpoint Manager to correspond to a different account
• The configuration file Endpoint Manager is making available to the KX-TGP600 has different port numbers (for each line) for Proxy Server Port, Presence Server Port, and Outbound Proxy Server Port.

Is this a defect? Or expected behavior and there is another area of my configuration that I have to modify to keep these ports at 5060 versus incrementing by 10 for each line?

screens.png1750x1078 142 KB

This topic was automatically closed 7 days after the last reply. New replies are no longer allowed.

This topic was automatically closed 7 days after the last reply. New replies are no longer allowed.

There was no need to hit “Check Online” at all. the module was already updated. Clicking the minus would have removed the message.

Let’s put this another way.
RFC2435 is from 2005. So why has Asterisk never supported it?

@tlewis You are getting very defensive for no reason. No one is claiming that Sangoma failed to do something here.

But what is being pointed out is that Asterisk needs to be updated to follow standards. This is why standards exist. Will it happen during the life of Asterisk 16? 17? /shrug No idea. But it should happen.

I also said in my earlier post that I feel Yealink’s actions were also overboard. Making a change that affects things at this scale, obviously without any testing of the change, is bad.

Edit: Yes, I know that a RFC is not a Standard, and RFC 4235 was never made a standard. It was also updated by RFC 7463 in 2015. I am also not someone that is so deep into the Protocol, that I know if Yealink actually followed this correctly or not.

In your case that worked. The reason I wrote this post was the fact that when I hit the minus button the warning did not disappear. Nothing I did made the notification remove itself. Time took care of the issue in my case as might apparently have for others.
Therefore the post that such was a bug from one of the developers and to report it.

Not at this time but it is being worked on

It will be though an HA commercial module

Different than the old one, yes.