Outgoing call won't work
Make sure there is a balance in the account. Make sure the registration string is correct: User:password@server.voip.msserver must be the one where the DID is registered. Why are you not using IAX2 to...
View ArticleFPBX13 RC, G722 and 1-way audio - even to voicemail
Another data point, ran into this 'feature' again today on an HTEK UC806 with firmware ver. 1.0.3.91. No audio until I forced it to use g722.
View ArticleFax Pro Outbound Fax Resolution
I'm Talking about Freepbx 12 with asterisk 11.18 in Cyberlynk, I'm having this problem and I don't know how to fix it, thank you Freepbx Fax Pro
View ArticleFax Pro Outbound Fax Resolution
You need to upgrade to FreePBX 13 and then get the newest FaxPro. That is the only way.
View ArticleCustom AGI script for outbound call checks stopped working
I'm still having this issue. To clarify a few things. I wrote this script, what it does is take any outbound call and checks the number against a do not call list and existing customer list. But...
View ArticleCustom AGI script for outbound call checks stopped working
Here is output when call doesn't record -- Executing [1712NXXXXXX@from-internal:1] Macro("SIP/7250-000313cb", "user-callerid,LIMIT,EXTERNAL,") in new stack -- Executing [s@macro-user-callerid:1]...
View ArticleCustom AGI script for outbound call checks stopped working
As I said before, turn on AGI debugging and liberally sprinkle your code with debugging output. If you care to post the whole AGI script, someone might be able to help you.
View ArticleCustom AGI script for outbound call checks stopped working
AGI debug was on for those copy and paste. The entire code is up a few posts, but as I said it has nothing to do with the code because even with only those few lines of code the same behavior is...
View ArticleCustom AGI script for outbound call checks stopped working
I see no attempts at debug output, AGI writes to stdout and reads from stdin, php can do that also. Start here:- http://www.voip-info.org/wiki/view/Asterisk+AGI+php
View ArticleFreePBX 13 - WAV files won't play
@tm1000 @lgaetz In an effort to move away from PiAF and install a stand alone version of FreePBX, I decided to warp up a server running CentOS 7 and installing FreePBX 13, following the guide that...
View ArticleCustom AGI script for outbound call checks stopped working
debug voice*CLI> agi set debug onAGI Debugging Enabled == Using SIP RTP TOS bits 184 == Using SIP RTP CoS mark 5 [INSERT INTO cel...
View ArticleClik here to view.
FreePBX 13 - WAV files won't play
Thanks for the quick reply, Andrew.. But Asterisk is started.. I even ran the command service asterisk restart and service asterisk start. However, I noticed that I was running it on Safari browser....
View ArticleClik here to view.
FreePBX 13 - WAV files won't play
@tm1000 So, I don't get the error when I am using Chrome, but I get it when I am using Safari ... weird. However, if I change settings and click the red Apply Config button from the GUI it vomits this...
View ArticleClik here to view.
FreePBX 13 - WAV files won't play
gforceco: Unable to connect to remote asterisk (does /var/run/asterisk/asterisk.ctl exist?) The problem is right there ^ Asterisk is not running. It might be running as root but that is just as bad....
View ArticleEndpoints continually register and increase port numbers
Found an issue with the router firmware on the remote end. Cisco RV082 with firmware 4.1, upgraded to 4.2 and problem solved.
View ArticleCustom AGI script for outbound call checks stopped working
OK, I would suggest you get two ssh sessions going on one, tailf /var/log/asterisk/full|grep -E "AGI" on the other, rasterisk -x Now, you will see why further debug output is needed . . . the lines in...
View Article3 rings, stop, other 3 rings etc
Helloafter my new installation i have a little problem:When i receive 1 call, my phone make 3 rings, after stop and after begin for other rings. What i can configure for not have this stop after 3...
View ArticleFreePBX Endpoint Manager Add Brand "An error occurred"
Any luck in finding a solution? I am in the same boat. Fresh install , version 12.0.76.2 and when I go to add brands, I get "An error Occured" as well.
View Article3 rings, stop, other 3 rings etc
Caller*ID, Fax detection, incorrect provisioning of a PSTN line . . . You need to describe your system and setup very precisely.
View Article