Edit Config Setting on Polycom Phone
So I bought and setup the End Point Manager module, and after provisioning the phones that way, using 4.1.7 firmware, the intercom/paging works as it should. Obviously, I could have provisioned them...
View ArticleProblems Upgrading UCP Node
Works fine here. Perhaps try to uninstall it. Also remove the pid it's talking about.
View ArticleUCP Node is not running
An issue has been filed for this at http://issues.freepbx.org/browse/FREEPBX-10725
View ArticleChanging voicemail email template in FreePBX 13
Works for me. Please ensure there are no outstanding module updates on the system and confirm what you are using for the body by pasting here between code tags. Of note, the variable place holders you...
View ArticleTranslate.c:341 Warning, NCH Dial Dictate drops call, RTP timeout same...
Hello, I've installed a trial of NCH Dial Dictate and added a standard extension for it. The extension registers and calls to the extension work; two way audio, DTMF everything works as expected. The...
View ArticleTranslate.c:341 Warning, NCH Dial Dictate drops call, RTP timeout same...
RTP Timout is controlled under Settings, Asterisk SIP Settings, Chan_SIP settings and defaults to 30s. Sounds like you need it increased.
View ArticleCallcentric outgoing caller ID no longer working
Screen Grab of config in FreePBX Not sure what changed, but this all use to work until some time a few weeks ago. Only real changes to the setup have been editing extension_custom.conf
View ArticleEndpoint Manager and Digium D50
Hello, Not hearing back from anyone, but thankful some folks looked at it, today I took out the installation disks, and rebuilt the server. Completely stayed away from the Digium module, as I am going...
View ArticleClik here to view.
Endpoint Manager and Digium D50
!! SOLVED !! Ok, the problem was the Buffalo SmartWeb switch! Some of the fields for DoS were enabled, and apparently that caused the 5060 traffic to be seen as a Denial of Service, and the switch was...
View ArticlePreserve Alert-Info header
Trying to use Polycom's built-in intercom feature, which sets the Alert-Info header on the outbound INVITE. Asterisk does not pass this on of course; is there some custom dialplan I can create so this...
View ArticleBlock an extenension making external calls
Appreciate all the help the routing module is working in my outbound route I can allow or block an extension completely wonderful would now like to allow certain number to be dialled and certain...
View ArticlePower Failure
Did not work for me. I got this ... error : Not enough memory for blob at 2170384 (need 1944068709)status : Operation failed Maybe I should the attempt to repair in MySQL...
View Articlefail2ban started banning vitelity
Is everyone else fixed or something? I added iptables rules to my freepbx server. I'm wondering if everyone else did the same, and maybe that screwed up? *mangle :PREROUTING ACCEPT [1103:1400664]...
View ArticleClik here to view.
Power Failure
GeekBoy: Not enough memory for blob at Solved for me.. Just in case others have same issue in future Was able to recover it using the following command myisamchk --max-record-length=1048576 -r -f...
View Articlefail2ban started banning vitelity
I understand. The thing I'm wondering is that I added chains to accept 5060 only from my sip provider's proxy. Since doing that it seems that fail2ban started blocking them (vitelity in one case,...
View ArticleSend Jabber alert for outgoing call
Hello all! I have followed the directions here "http://nerdvittles.com/?p=1434" to setup incoming alerts, and it works like a charm! I would like to however do the same for outgoing as well.Would...
View ArticleFreePBX version listing did not update from 12 to 13
was on 6.12.65-31, ran the upgrader from GUI and it updated but still shows the 6.12.65-31 in both the GUI and the CLI. The system functions (except WebRTC and PJSIP) and I have the new GUI look and...
View ArticleEdit Config Setting on Polycom Phone
Note also you could have just updated the database to pass "Ring Answer" instead: UPDATE paging_autoanswer SET setting="Alert-Info: info=Ring Answer" WHERE useragent="Polycom" AND var="ALERTINFO";...
View ArticleI cant access to Frepbx GUI!
Could be a billion different reasons, but without anything from you we could be guessing all day.You have not included any information about what you did, or any information about your setupNot...
View Article